Information Here

 

 

This post listed below involving A Step-by-Step Guide to Installing a Bathtub is quite attention-grabbing. Have a go and make your own final thoughts.

Mounting a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, as well as sometimes, tiling skills. Changing an old tub with a brand-new one is likewise a reasonably tough project. If the old bathtub is readily available, the task can move easily; if you have to open up a wall to get rid of the old tub and place the new tub, the job is much harder. In either instance, the project is within a residence handyman's skills, although you will certainly require a helper to vacate the old tub as well as embeded in the new one. Make certain you have actually qualified on your own for the job as well as fit attempting it. Instead of working with a professional to take control of a halfway-completed task, it is better to think about utilizing one prior to you begin. Possibilities are you might require a professional plumber to make tube links.
This write-up will assist you mount a new tub in your shower room if you have actually already purchased a new bathtub and also don't need to transform the setup of your previous supply of water pipes.
Your devices and also product checklist ought to make up the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Planning for the Installment

Firstly, the supporting frame provided with the bathroom should be fitted (if required) according to the manufacturer's directions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to make certain that if the tap comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the adaptable faucet adapters to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you utilize every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath must now prepare to be fitted in its last setting.

 

 

Removing Old Touches

If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is disconnect the water. After doing so, activate the faucets to drain pipes any kind of water staying in the system. The process of eliminating the existing taps can be quite bothersome due to the restricted access that is often the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipelines have been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from turning during this process. When the taps have been removed, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.

 

 

Mounting the Bathtub

Making use of both wooden boards under its feet, place the bathtub in the required setting. The wooden boards are valuable in uniformly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 little factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be accomplished by inspecting the level and also adjusting the feet on the bathtub until the spirit level reads level.
To install faucets, fit all-time low of the furthest adaptable tap connector to the suitable supply pipe by making a compression join; then do the same for the other faucet.
Switch on the water and also examine all joints and new pipework for leaks and tighten them if necessary. Fill the bathtub and also check the overflow outlet as well as the regular electrical outlet for leakages.
Lastly, take care of the bathroom paneling as explained in the maker's instruction manual. Tiling as well as sealing around the bathtub ought to wait until the bath tub has actually been utilized at the very least when as this will certainly resolve it right into its last placement.

 

 

Suitable New Touches

If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the faucet and also the various other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in place in between the faucet and also the sink. Safeguard the faucet in place with the manufacturer provided backnut. When the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The previous type must be linked to the faucet finishes first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.

 

 

Tiling Around the Bath tub

In the location where the bathroom satisfies the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to crack a stiff seal, causing the water to pass through the wall between the bath and the tiling, leading to complications with wetness as well as possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures and also installations. They are offered in tubes and cartridges, and can securing gaps up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill up the tub with water before sealing, to permit the movement experienced when the tub is in usage. The sealer can split relatively early if you do not take into account this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily offered on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof adhesive as well as grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Hopefully you liked our post about Tools You Need to Install a New Bathtub . Many thanks for finding the time to browse our post. Sharing is caring. You just don't know, you may be helping someone out. I am grateful for your time. Please come visit our website back soon.

This Resource